Evolve3D Air Venturi Avenge-X Barrel Band with Pic Rail

MATERIAL 3D Printed PETG  INSTALLATION Purchase includes two parts (threaded base, and Cap). 1. Unscrew existing metal foster cap and set aside. 2. Screw 3D printed base onto foster fitting ensuring that it is straight while tightening. It will seat flush against tube or bottle as shown in photos. NOTE: Threads were designed with some friction so that the base will not move once tightened down. 3. Cap can now be snapped into place over top of foster fitting. DISCLAIMER The purchase includes only the 3D printed parts. All other objects in photos are for reference only. USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product. WARRANTY We offer a limited lifetime warranty on our 3D printed parts.

MATERIAL: 3D Printed PETG INSTALLATION: Purchase includes 3D printed barrel band assembly and M3 Mounting Hardware.  WARNING! Confirm air gun is unloaded and safe before beginning installation.  1. Remove any barrel accessories from the end of the shroud (moderators, thread protector, etc) 2. Remove the threaded foster fill cap from the end of the tube (not required for bottle models). 3. Slide barrel band assembly over shroud and tube/bottle.  NOTE: This will be snug and may require you to separate the barrel band by pulling out on the sides or squeezing the top and bottom while working it into place. Be careful not to peel up the silicone friction pads while you are sliding it into place.  4. Secure barrel band assembly, using m3 screw, by hand tightening until snug. Do not over-torque!  DISCLAIMER: The purchase includes only the 3D-printed parts. All other objects in the photos are for reference only.  USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product.  WARRANTY: We offer a limited lifetime warranty on all of our 3D-printed parts.

AEA AIRGUNS - DEFENDER - Barrel Housing / Upper - Made In USA - Fox 2 Industries  Designed to replace the factory barrel housing on the AEA Airguns Defender PCP Pistol.  This is the result of continuous development on our barrel supports for the Defender. With this, you get the stability the Defender lacks in stock form, and you get a more streamlined look.  Features Tru Glo front sight, and dovetail mounting location under the muzzle.  Made with super durable Nanotechnology polymer PA.  Measures 140mm x 44.5mm x 24mm  Made in Maine, USA

MATERIAL: 3D Printed PETG INSTALLATION: Purchase includes 3D printed barrel band assembly and M3 Mounting Hardware.  WARNING! Confirm air gun is unloaded and safe before beginning installation.  1. Remove any barrel accessories from the end of the shroud (moderators, thread protector, etc) 2. Remove the threaded foster fill cap from the end of the tube (not required for bottle models).  3. Slide barrel band assembly over shroud and tube/bottle.  NOTE: This will be snug and may require you to separate the barrel band by pulling out on the sides or squeezing the top and bottom while working it into place. Be careful not to peel up the silicone friction pads while you are sliding it into place.  4. Secure barrel band assembly, using m3 screw, by hand tightening until snug. Do not over-torque!  DISCLAIMER: The purchase includes only the 3D-printed parts. All other objects in the photos are for reference only.  USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product.  WARRANTY: We offer a limited lifetime warranty on our 3D-printed parts.

STYLES Tube Model - Barrel band design with integrated pic rail across the top. Choose this style if you have the Tube version of the Avenge-X. Bottle Model - Dual screw clamp design with integrated pic rail on top. Choose this style if you have the Bottle version of the Avenge-X. **Bottle style will not work on tube models due to clearance issues with the foster fitting cap.  MATERIAL 3D Printed PETG  INSTALLATION Purchase includes 3D printed mount and M3 Mounting Hardware. WARNING! Confirm air gun is unloaded and safe before beginning installation. 1. Remove any barrel accessories from end of shroud (moderators, thread protector, etc) 2. Remove threaded foster fill cap from end of tube (not required for bottle models). 3. Slide assembly over shroud. NOTE: This may be snug and require you to separate barrel band version by pulling out on the sides or squeezing the top and bottom while working it into place. 4. Secure assembly, using m3 screw(s), by hand tightening until snug. Do not over torque! DISCLAIMER The purchase includes only the 3D printed parts. All other objects in photos are for reference only. USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product. WARRANTY We offer a limited lifetime warranty on our 3D printed parts.

MATERIAL: 3D Printed PETG INSTALLATION: Purchase includes 3D printed barrel band assembly and M3 Mounting Hardware.  WARNING! Confirm air gun is unloaded and safe before beginning installation.  1. Remove any barrel accessories from the end of the shroud (moderators, thread protector, etc) 2. Remove the threaded foster fill cap from the end of the tube (not required for bottle models).  3. Slide barrel band assembly over shroud and tube/bottle.  NOTE: This will be snug and may require you to separate the barrel band by pulling out on the sides or squeezing the top and bottom while working it into place. Be careful not to peel up the silicone friction pads while you are sliding it into place.  4. Secure barrel band assembly, using m3 screw, by hand tightening until snug. Do not over-torque!  DISCLAIMER: The purchase includes only the 3D-printed parts. All other objects in the photos are for reference only.  USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product.  WARRANTY: We offer a limited lifetime warranty on our 3D-printed parts.

MATERIAL 3D Printed PETG  INSTALLATION Purchase includes two parts (Clamp-on base and Cap). WARNING! Confirm air gun is unloaded and safe before beginning installation. 1. Remove the existing rubber cap from the foster fitting. 2. Slide clamp-on base onto the end of the tube over the foster fitting until fully seated against end of tube. 3. Tighten the M3 screw using hand tool until clamp-on base is secure. DO NOT over torque. 4. Cap can now be snapped into place over top of foster fitting. DISCLAIMER The purchase includes only the 3D printed parts. All other objects in photos are for reference only. USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product. WARRANTY We offer a limited lifetime warranty on our 3D printed parts.

Whats Included? 1x 3D Printed Barrel Band (PETG) Pre-installed Silicone Friction Pads M3 Mounting Hardware (screws and square nuts)   COMPATIBILITY Designed for the Umarex Gauntlet 2. INSTALLATION  WARNING! Before installing any accessories, always ensure your airgun is unloaded and safe. Do not fully loosen the screws during installation, as the M3 square nuts may fall out of the barrel band slots. 1. Prepare for Installation - Remove any existing accessories from the barrel that could interfere with the barrel band. 2. Position the Barrel Band - Slide the barrel band over the bottle and shroud, carefully working it into place. If needed, apply a small amount of silicone-safe lubricant to ease installation. 3. Secure the Barrel Band - Hand-tighten the assembly until snug. Do not over-torque the screws.  DISCLAIMER The purchase includes only the 3D printed part and mounting hardware. All other objects in photos including the airgun are for reference only.  USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product.  WARRANTY We offer a limited lifetime warranty on our 3D printed parts.

Fits MIL- STD-1913 rails. Tough Nanotechnology PA Material. Measures 2.3x1.7x1.2

Picatinny Mount Tactical Flashlight. Designed for 21mm Picatinny rails. Up to 300 lumens and 100k hours lifetime. 4.85 inch overall height, 3.6 inch overall length, 1.4 inches overall width. Push button on/off end cap.

Ultra-Powerful Brightness: Light up your path with this flashlight that boasts 2000 lumens of brightness, capable of reaching distances of up to 656 feet. With over 50,000 hours of lifespan, this flashlight will guide you through any adventure. Designed to withstand extreme weather conditions, our flashlights' high lumens is an essential tool for outdoor enthusiasts.  Zoomable and Multi-Mode: Choose from five different modes on our LED flashlight, including low, medium, high, SOS, and strobe. Whether you are camping, hunting, hiking, biking, or facing a power outage, these versatile modes have got you covered. The adjustable focus allows you to switch between a spot and a flood beam, providing a clear view of your surroundings.  Aircraft-Grade Material: This tactical flashlight ensures durability, waterproofness, dustproofness, and wear resistance. The ultra-dense fine-grained non-slip design offers a comfortable grip for an enhanced user experience. Designed to fit milstd1913 Picatinny rails, this tactical flashlight will give you a good grip on any situation. Utilizes 3 AAA disposable alkaline batteries which are included.

Full-length clamping guarantees a rock-solid foundation for your airgun accessories. Made for AirForce sporting air rifles and the TalonP air pistol, the Tri-rail lets you load up your air gun with lots of accessories that make hunting and shooting a lot more fun...and also increases accuracy.

AirForce Spin Loc Carbon Fiber Upgrade/Spare Tank for .457-Cal Texans

AirForce Spin-Loc Carbon Fiber Upgrade/Spare Tank for .50-Cal Texans

MATERIAL 3D printed PETG INSTALLATION Purchase includes two parts (threaded base, and Cap).  WARNING! Confirm air gun is unloaded and safe before beginning installation. 1. Unscrew existing metal foster cap and set aside. 2. Screw 3D printed base onto foster fitting ensuring that it is straight while tightening. It will seat flush against tube or bottle as shown in photos. NOTE: Threads were designed with some friction so that the base will not move once tightened down. 3. Cap can now be snapped into place over top of foster fitting.   DISCLAIMER The purchase includes only the 3D printed parts. All other objects in photos are for reference only  USE this product at your own risk. EVOLVE 3D, LLC is not liable for damage to your property or person while using this product.  WARRANTY We offer a limited lifetime warranty on our 3D printed parts.

AirForce Fast Attach Thread System, Fits Condor

AirForce CO2 Adapter, Fits Condor, Talon & Escape PCPs

How to switch from high-pressure air to CO2:

Compatible with: