50A A-Series Raised Rocker Circuit Breaker - Double Pole

The Blue Sea System Push Button Thermal Circuit Breaker is ideal for 24-hour circuit protection. This circuit breaker has a push to reset operation and a "Trip Free" design that cannot be held "ON" during fault current conditions. It is ignition protected, making it safe for installation aboard gasoline-powered boats. The circuit breaker is incorporated into Blue Sea Systems Waterproof Circuit Breaker panels and main Battery Main Distribution Panels.

• Part Number:
• Color: Blue
• Amperage: 20A
• Terminal Type: Quick Connect

• Push to reset operation
• "Trip Free" design cannot be held "ON" during fault current condition
• Ignition protected - Safe for installation aboard gasoline powered boats
• Incorporated into Blue Sea Systems Waterproof Circuit Breaker panels and main Battery Main Distribution Panels

Protect your DualBus PN 2701 with this s Cover. This cover is designed to fit perfectly over the DualBus PN 2701, providing protection and preventing accidental contact. Made by s, a trusted manufacturer of marine electrical products.

• Manufacturer Part No:
• UPC: 63208504

• Designed to fit DualBus PN 2701
• Provides protection and prevents accidental contact
• Made by trusted marine electrical product manufacturer s

Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to type thql with the same design and performance, yet only taking up 1/2 the space. 1/2 in. Per pole. 15 to 25 amp 14 - 8 cu or 12 - 8 al awg wire, 30 to 50 amp 8 - 4 cu or 8 - 2 al awg wire.

• 120/240 volt
• 10,000 air.
• Plug-in - Double pole
• Type thql - Common trip
• Factory installed lugs
• Size - 0.5 in.
• Amp rating - 40
• Dimension - 3-9/32 h x 1/2 w x 2-3/8 d in.
• Item weight - 0.43 lbs.

• For ATO/ATC fuses
• Interlocking modules snap together
• Flame resistant reinforced polyester base
• 1/4" tin plated copper tab terminals
• 6 Gang w/ground bus bar

• Rated: 30A/circuit;160A total block
• Part Type: Marine Fuse Blocks
• Total Circuit Quantity: 6
• Constant Hot Circuit Quantity: 1
• Fuse Style: ATO/ATC
• Weight: 0.501 lbs

Our APC Back-UPS is a reliable and durable power supply for all kinds of electronic devices. This product is known for its high efficiency, honesty, and comprehensive services. With hundreds of mind-blowing innovations and creativity, our exclusive products are of the highest quality and standard.

• Power Capacity: 600 VA
• Volts: 120V
• Interface Port: USB

• APC Back-UPS
• 5-foot line cord with NEMA 5-15 right-angle plug end
• PowerChute Personal Edition software
• USB cable

AC 6 PositionPN: White SwitchesFeaturesAll hot neutral and safety ground buses installed fully pre-wiredLabel backlighting pre-installedDetailed installation instructions and cutout templateAll LEDs installedMaximum panel Amperage - 100 Amperes(6) 15A Single Pole Circuit Breaker120 VoltProduct : BLUE SEA BREAKER PANEL 120VAC 6 POS Manufacturer : Manufacturer Part No : UPC : 63208506

• Maximum panel Amperage - 100 Amperes
• (6) 15A Single Pole Circuit Breaker
• 120 Volt

• All hot neutral and safety ground buses installed fully pre-wired
• Label backlighting pre-installed
• Detailed installation instructions and cutout template
• All LEDs installed

Upgrade your electrical system with the GE Electrical TLM812FCUDP Loadcenter. This compact and lightweight loadcenter provides optimum wire-bending space and features a side-mounted main breaker for top or bottom feed. The copper bus and galvanized box increase durability and reliability, while the tinplating provides corrosion resistance. The loadcenter accepts GE Q-line branch circuit breakers, including GE's exclusive 1/2 in. THQPs. The interior is easy to remove and reinstall. Main breaker not included.

• Amp rating - 125
• 8 circuit
• Neutral terminations - 100%
• Neutral hole rating - 14-4 wire
• Dimensions - 12-5/8 x 12-3/8 x 3-3/8 in.
• Item weight - 8.2 lbs.

• Compact and lightweight design
• Extruded neutrals for easy wiring
• Combination slotted/robertson screws for fast wiring
• Accepts GE Q-line branch circuit breakers

For federal pacific load centers. Hacr rated. 120/240 volt ac, 10,000 aic. Plug-in Type ubi-f. Double pole - 1/2 in. Space. Amp rating - 20a. Item weight - 0.39 lbs.

• For federal pacific load centers.
• Hacr rated.
• 120/240 volt ac, 10,000 aic.
• Plug-in
• Type ubi-f
• Double pole - 1/2 in. Space
• Amp rating - 20a
• Item weight - 0.39 lbs.

• For federal pacific load centers.
• Hacr rated.
• 120/240 volt ac, 10,000 aic.
• Plug-in
• Type ubi-f
• Double pole - 1/2 in. Space
• Amp rating - 20a
• Item weight - 0.39 lbs.

• Height: 11.05"
• Width: 8.22"
• Depth: 3.61"
• Ground connector
• Top feed, ring-less, no bypass
• Surface mount
• NEMA 3R rated

• Dimension: 4.8" H x 8.8" W x 12.5" L
• Weight: 13 lbs

If you are a gadget lover, our Electronics catalog is your dream destination. Choose from hundreds of gadgets and accessories to suit different uses and add some entertainment, facility and convenience to your life.

• Fuse Function: Fast Acting
• Finish: Nickel - Plated Brass Endcap
• Fuse Type: GMA Glass Tube
• Voltage: 125 V

• Lots of options in every category
• High quality construction and modern designs
• Superior quality performance and reliability
• Competitive prices and value for money
• Fast acting glass cartridge fuses for testers & other small electronic equipment requiring fuses

• 24"/0.61m Durable Steel Hardwired Power Strip
• With Ears (Mounting Tabs) on both Ends, 2 x 0.67/17mm, Total Length 25.28"/642mm
• 6 Black US NEMA 5-15R Tamper Resistant Outlets, Vertical Orientation
• 2 USB Ports, (Type A) Output DC 5V/2.1A, Input AC 110-240V/0.5A/60Hz)
• Hardwired without Power Cord for Mounting at Your Desired Location
• ETL Approved and Listed (Conforms to UL 5, UL 1310 and CAN/CSA C22.2 No. 62)
• Electrical Ratings: 125V/15A/60Hz/Recommended Max Load 1440W Ample Space between Outlets
• 6 Easily Punched off Knockouts on Each Side C (Top/Bottom Cover, Both Sides and Ends)
• Back Cover Easily On/Off, Where Wires Are Connected
• Wires Readily Striped for Easier Removal and Faster Installation
• Great for Contractors, Electricians and Installers, as well as DIYers

• Before installation, you may need to get a 3/8" wire clamp connector and 3 wire connectors (or terminal connectors). Decide your wire gauge, and ask store attendant for assistance what connectors you should get) from your local hardware, electric supply or home improvement stores
• Minimum tools required: A fine to medium fine philips screw driver, and a pair of scissors, and a pair of mid size slip joint pliers, Turn off electricity in the house.Decide where to place this Hardwired Power Strip unit, Choose the knockout to be used for cord exit, then gently punch it off with the back of a screw driver or other tool handy,Unscrew the back cover off the unit with a philips screw driver
• Take out the white/transparent plastic insulation sheet, and use a pair of scissors to cut a hole on it (about 3/4" in diameter, or big enough for) WHERE the wires will run through. If the bottom knockout on the back cover is to be used for wire connection, a wire clamp connector may not be needed, thus, please ignore step 6, 7 and 9 below
• Put on the 3/4" wire clamp connector in place. Secure its installation by tightening the big ring screw (inside the casing) with the pair of slip joint pliers
• Run the wires through the wire clamp connector, from outside into the Unit. In case bottom knockout on the back cover is to be used for wire connection, please run the wires through the back cover first and then the plastic insulation sheet, now with the knockout coin punched off, from outside to inside Match the colored wires and secure the wire connection with proper wire connectors Tighten the two pressure screws properly on the wire clamp connector Place the plastic insulation sheet back and screw the back cover on

• For unit with ears (mounting tabs on both ends): mount the unit through the ears with screws provided
• For unit without ears, place the unit where it is intended to be, mark where to install clips, secure the clips with screws provided. Then snap the unit in onto the clips
• For models without ears up to 24, and models with ears above 30, mounting holes on the back cover could be used to secure the unit (but a unit CANNOT be installed with such mounting holes if the unit is to be placed against a wall/cabinet on the side since the unit cannot be reinstalled onto the back cover). Then, please mount the back cover first and then carefully screw the unit onto the back cover Turn electricity back on, it is ready to go

• Size: 24 in.
• Outlets: 6
• Dimension: 24 x 1.61 x 1.16 in. (610 x 41 x 29.5mm)
• Weight: 2 lbs

• Built with a plated, aluminum bus bar.
• Indoor - Plug-On
• Flush/Surface
• Amp Rating - 100
• Value Pack
• Spaces/ Circuits - 20/40

• 200a trailer park load center
• Outdoor mount
• 4 space circuit
• 8 single poles
• Full capacity feed thru & neutral lugs
• Use ds hub
• Gbk14p ground bar if required
• Hub included.
• Dimension - 6 x 11.7 x 26 in.
• Item weight - 21.15 lbs.

It's the largest 12 Volt Jump-N-Carry unit we manufacture. With 2000 Peak Amps of starting power, it will spin the starters on all class 1-6 commercial trucks. Plus, its heavy-duty Clore PROFORMER battery satisfies the most aggressive portable power users. Its onboard automatic charger can provide up to 24 Hour/365 Day continuous charging.

• 2000A Peak 12V Jump Starter
• 2000 Peak Amps
• Automatic charging mode
• Battery status indicator gauge
• Extra heavy-duty polyethylene case
• DC outlet to power 12 Volt accessories
• Assembled in USA

The inverter converts 12 volts DC to 1000 watts and uses pure sine-wave output. Advanced technology such as wide DC input voltage, wide operation temperature with an output voltage selectable dip switch. Overall, this inverter can be used for many applications and is extremely user friendly.

• Power ON / OFF remote control (Green Terminal)
• Remote controller CR-8 / CR-16 (optional)
• Input & Output fully isolation
• Temperature & Load controlled cooling fan
• Built in advance microprocessor to provide friendly interface
• Output frequency 50 / 60 Hz selectable by DIP switch
• Output voltage DIP switch selectable
• Adjustable power saving mode by variable resister
• 3-color LED status indicators
• Input protection - Reverse Polarity (Fuse) / Under Voltage / Over Voltage
• Output protection - Short Circuit / Overload / Over Temperature
• E-13 / UL / CE / FCC approved
• Type - Pure sine wave
• Watts - 1000W
• Input Voltage - 12VDC
• Output Voltage - 120VAC
• Dimension - 14.65 x 7.87 x 3.27 in.