Top Unbeatable Sale Deals for October 2025

A contactor is an electrically-controlled switch used for switching an electrical power circuit. A contactor is typically controlled by a circuit which has a much lower power level than the switched circuit, such as a 24-volt coil electromagnet controlling a 230-volt motor switch.

• 220-240V 50 Hz & 240-264V 60 Hz Contactor
• Made with high quality material

• Voltage & Hertz: 220-240V 50 Hz & 240-264V 60 Hz
• Length: 4.05"
• Width: 4.65"
• Height: 2.4"

A pump is a device that moves fluids (liquids or gases), or sometimes slurries, by mechanical action. Pumps can be classified by their method of displacement into positive displacement pumps, impulse pumps, velocity pumps, gravity pumps, steam pumps and vacuum and valveless pumps. There are three basic types of pumps: positive displacement, centrifugal and axial-flow pumps. In centrifugal pumps the direction of flow of the fluid changes by ninety degrees as it flows over an impeller, while in axial flow pumps the direction of flow is unchanged. When a casing contains only one revolving impeller, it is called a single-stage pump. When a casing contains two or more revolving impellers, it is called a double- or multi-stage pump. Vacuum pumps are simply compressors that take in contained gas at a pressure lower than atmospheric pressure, compress it, and discharge the gas at atmospheric pressure creating a vacuum where the contained gas originated. A mechanical seal is a device that helps join systems or mechanisms together by preventing leakage (e.g. in a pump system), containing pressure, or excluding contamination. The effectiveness of a seal is dependent on adhesion in the case of sealants and compression in the case of gaskets or o-rings.

• Pump Seal Crane
• Made with high quality material

• Length: 1.55 in / 3.94 cm
• Width: 1.55 in / 3.94 cm
• Height: 0.85 in / 2.16 cm

A relay is an electrically operated switch. It consists of a set of input terminals for a single or multiple control signals, and a set of operating contact terminals. The switch may have any number of contacts in multiple contact forms, such as to make contacts, break contacts, or combinations thereof. Relays are used where it is necessary to control a circuit by an independent low-power signal, or where several circuits must be controlled by one signal.

• 16A 400V-120V AC USA Relay
• Made with high quality material

• Voltage: 400V-120V AC
• Amperage: 16A
• Length: 4.4"
• Width: 5.45"
• Height: 2.4"

Pumps and fans of various types and sizes are used in all kinds of restaurant equipment. The main internal component of these pumps and fans is the impeller. The impeller is a rotor blade designed to increase the pressure and flow of air, gases or fluids.

A pump is a device that moves fluids (liquids or gases), or sometimes slurries, by mechanical action.

Pumps can be classified by their method of displacement into positive displacement pumps, impulse pumps, velocity pumps, gravity pumps, steam pumps and vacuum and valveless pumps. There are three basic types of pumps: positive displacement, centrifugal and axial-flow pumps. In centrifugal pumps the direction of flow of the fluid changes by ninety degrees as it flows over an impeller, while in axial flow pumps the direction of flow is unchanged. When a casing contains only one revolving impeller, it is called a single-stage pump. When a casing contains two or more revolving impellers, it is called a double- or multi-stage pump.

Vacuum pumps are simply compressors that take in contained gas at a pressure lower than atmospheric pressure, compress it, and discharge the gas at atmospheric pressure creating a vacuum where the contained gas originated.

• USA Pump Impeller
• Made with high quality material

• Length: 2.45"
• Width: 3.7"
• Height: 2.6"

Motors are used in all kinds of restaurant equipment to power beaters, blenders, slicers, basket lifts, filters, fans and much more. A motor converts one form of energy into mechanical energy. Electric motors convert electrical energy into mechanical motion, pneumatic motors use compressed air. A motor is a device driven by electricity, air, or hydraulic pressure, which does not change the chemical composition of its energy source.

Electric motors may be classified by considerations such as power source type, internal construction, application and type of motion output. In addition to AC versus DC types, motors may be brushed or brushless, may be of various phase (see single-phase, two-phase, or three-phase), and may be either air-cooled or liquid-cooled. General-purpose motor designs with standard dimensions and characteristics provide convenient mechanical power for foodservice equipment once customized to the exact OEM specifications (RPM, torque, magnet dimension, winding, etc.).

• Long 6000N Pro Thermic Tilting Motor
• Made with high quality material

• Length: 7.2"
• Width: 18.55"
• Height: 5.2"